Many homeowners wait until their water heater fails before shopping for a replacement. Because they are in a hurry to regain their hot water supply, they are often unable to take the time to shop for the most energy efficient unit for their specific needs. This is unfortunate, because the cost of purchasing and operating a water heater can vary greatly, depending on the type, brand, and model selected, and on the quality of the installation.
To avoid this scenario, do some research now before you are faced with an emergency purchase. Familiarize yourself today with the options that will allow you to make an informed decision when the need to buy a new water heater arises.
Remember, most if not all jurisdictions require a plumbing permit for a replacement or new water heater. Most places understand that if your water heater goes out over the weekend you will be replacing it immediately, and allow you to come in on Monday to file the permit.
Within the last few years, a variety of water heaters have become available to consumers: conventional storage, demand, heat pump, tankless coil, indirect, and solar. It is also possible to purchase water heaters that can be connected to your home's space heating system.
Storage Water Heaters
A variety of fuel options are available for conventional storage water heaters electricity, natural gas, oil, and propane. Ranging in size from 20 to 80 gallons (75.7 to 302.8 liters), storage water heaters remain the most popular type for residential heating needs in the United States. A storage heater operates by releasing hot water from the top of the tank when the hot water tap is turned on. To replace that hot water, cold water enters the bottom of the tank, ensuring that the tank is always full.
Because the water is constantly heated in the tank, energy can be wasted even when no faucet is on. This is called standby heat loss. Newer, more energy efficient storage models can significantly reduce the amount of standby heat loss, making them much less expensive to operate. To determine the most energy efficient model, consult the Energy Guide label required on storage water heaters. Energy Guide labels indicate either the annual estimated cost of operating the system or energy efficiency ratings.
TIP: Doityourself’s plumbing consultant Wayne McCarthy suggests, “If you have an electric water heater and are considering a gas one, look into the cost of running the vent pipe to the outside and a gas line to the heater itself. The same thinking applies when converting from gas to electric. How much will it cost to run wiring to the water heater and is your electric service big enough for the additional load?”
Demand Water Heaters
It is possible to completely eliminate standby heat losses from the tank and reduce energy consumption 20 to 30 percent with demand (or instantaneous) water heaters, which do not have storage tanks. Cold water travels through a pipe into the unit, and either a gas burner or an electric element heats the water only when needed. With these systems, you never run out of hot water. But there is one potential drawback with demand water heaters--limited flow rate.
Typically, demand heaters provide hot water at a rate of 2 to 4 gallons (7.6 to 15.2 liters) per minute. This flow rate might suffice if your household does not use hot water at more than one location at the same time (e.g., showering and doing laundry simultaneously). To meet hot water demand when multiple faucets are being used, demand heaters can be installed in parallel sequence. Although gas fired demand heaters tend to have higher flow rates than electric ones, they can waste energy even when no water is being heated if their pilot lights stay on. However, the amount of energy consumed by a pilot light is quite small.
There are electric tankless on demand water heaters available. These range in size from ones mounted under a sink to whole house. The small ones are ideal for that half bath with no tub or shower as you only have to run a cold water line.
Heat Pump Water Heaters
Heat pump water heaters use electricity to move heat from one place to another instead of generating heat directly. To heat water for homes, heat pump water heaters work like refrigerators in reverse.
Heat pump water heaters can be purchased as integral units with built-in water storage tanks or as add-ons that can be retrofitted to an existing water heater tank. These systems have a high initial cost. They can also only be installed in locations that remain in the 40 to 90 degrees F (4.4 to 32.2 degrees C) range year round, and contain at least 1000 cubic feet (28.3 cubic meters) of air space around the water heaters. To operate most efficiently, they should be placed in areas having excess heat, such as furnace rooms. They will not work well in a cold space.
Tankless Coil and Indirect Water Heaters
A home's space heating system can also be used to heat water. Two types of water heaters that use this system are tankless coil and indirect. No separate storage tank is needed in the tankless coil water heater because water is heated directly inside the boiler in a hot water heating system. The water flows through a heat exchanger in the boiler whenever a hot water faucet is turned on. During colder months, the tankless coil works well because the heating system is used regularly. However, the system is less efficient during warmer months and in warmer climates when the boiler is used less frequently.
A separate storage tank is required with an indirect water heater. Like the tankless coil, the indirect water heater circulates water through a heat exchanger in the boiler. But this heated water then flows to an insulated storage tank. Because the boiler does not need to operate frequently, this system is more efficient than the tankless coil. In fact, when an indirect water heater is used with a highly efficient boiler, the combination may provide one of the least expensive methods of water heating.
Criteria for Selection
As with any purchase, balance the pros and cons of the different water heaters in light of your particular needs. There are numerous factors to consider when choosing a new water heater. Some other considerations are capacity, efficiency, and cost.
Although some consumers base their purchase on the size of the storage tank, the peak hour demand capacity, referred to as the first hour rating (FHR) on the Energy Guide label, is actually the more important figure. The FHR is a measure of how much hot water the heater will deliver during a busy hour, and it is required by law to appear on the unit's Energy Guide label. Therefore, before you shop, estimate your household's peak hour demand and look for a unit with an FHR in that range.
Gas water heaters have higher FHRs than electric water heaters of the same storage capacity. Therefore, it may be possible to meet your water heating needs with a gas unit that has a smaller storage tank than an electric unit with the same FHR. More efficient gas water heaters use various non conventional arrangements for combustion air intake and exhaust. These features, however, can increase installation costs.
TIP: Wayne adds, “Water heater sizing is based on FHR in accordance with plumbing codes. The UPC (Uniform Plumbing Code) states the minimum sizing shall be in compliance with table 5-1, that’s chapter 5 table 1. It is determined by how many bathrooms and bedrooms you have in your house. For example a 3 bedroom 2 bath house requires a FHR of 67 gallons. Keep in mind these are minimums. If you have a large Roman tub like mine, you might want to go with a larger FHR.”
Once you have decided what type of water heater best suits your needs, determine which water heater in that category is the most fuel efficient. The best indicator of a heater's efficiency is its Energy Factor (EF), which is based on recovery efficiency (i.e., how efficiently the heat from the energy source is transferred to the water), standby losses (i.e., the percentage of heat lost per hour from the stored water compared to the heat content of the water), and cycling losses.
The higher the EF, the more efficient the water heater. Electric resistance water heaters have an EF between 0.7 and 0.95. Gas heaters have an EF between 0.5 and 0.6, with some high efficiency models around 0.8. Oil heaters range from 0.7 to 0.85, and heat pump water heaters range from 1.5 to 2.0. Product literature from manufacturers usually gives the appliance's EF rating. If it does not, you can obtain it by contacting an appliance manufacturer association. Some other energy efficiency features to look for are tanks with at least 1.5 inches (3.8 centimeters) of foam insulation and energy efficiency ratings shown on the Energy Guide labels.
Another factor uppermost in many consumers' minds is cost, which encompasses purchase price and lifetime maintenance and operation expenses. When choosing among different models, it is wise to analyze the life cycle cost, the total of all costs and benefits associated with a purchase during its estimated lifetime. More information on conducting life cycle cost analyses is available from EREC.
Units with longer warranties usually have higher price tags, though. Often, the least expensive water heater to purchase is the most expensive to operate.
Wayne McCarthy, professional plumber, contributed to this article.
Article source: Link